Hi Cata,
thanks again. I will do the following to test if it works:
1) Get rid of the Black-Hole and install OpenATV (I think that is waht GigaBlue mostly uses)
2) USe your Script to stop enigma using anything
3) Start MiniSAT with your parameters and the right sourcing
Whch Image do you use?
And Finally - Is there a chance that you compile a new version including also CI? I think there happened a lot of thngs since your last version was compiled.
Thanks
S
minisatip binaries
Re: minisatip binaries
Hi,
I am not sure which image it runs (it's the default) as I have just remote access to the device...
Yes probably will compile a image with CI and netceiver when will get a bit of time....(vento needs one)...
I am not sure which image it runs (it's the default) as I have just remote access to the device...
Yes probably will compile a image with CI and netceiver when will get a bit of time....(vento needs one)...
Re: minisatip binaries
Hi,
One question that came to my mind: The main reason why I want to change my existing SATIp Server from Digital Devices is the CI+ Support. Gigablue has it on the actual devices.
Just to confirm: As lomg as the CI function is buil-in: Does it also support the SATIp streaming using a CI+ Module (for instance in GErmany HD+ or SKY)
o does it only Support CI (without + )
Thanks
S
Ok that's even better becaus ethan you do not have to modify the whole system. GoodI am not sure which image it runs (it's the default) as I have just remote access to the device...
One question that came to my mind: The main reason why I want to change my existing SATIp Server from Digital Devices is the CI+ Support. Gigablue has it on the actual devices.
Just to confirm: As lomg as the CI function is buil-in: Does it also support the SATIp streaming using a CI+ Module (for instance in GErmany HD+ or SKY)
o does it only Support CI (without + )
Thanks
S
Re: minisatip binaries
Hello,
I test a little bit and find out that thats work:
minisatip1 --dmx-source 0:1 -e 1 -u 0:0-1210,1:1-1420 -x 84 -l -f
my cable come in tuner b (tuner1) and I want to use both.
Is that the right parameter?
thanks
I test a little bit and find out that thats work:
minisatip1 --dmx-source 0:1 -e 1 -u 0:0-1210,1:1-1420 -x 84 -l -f
my cable come in tuner b (tuner1) and I want to use both.
Is that the right parameter?
thanks
Re: minisatip binaries
Hi,
I did some testing however no sucess
1) Installed nw Image (OpenATV). No signal
2) Tried different Adapter /Sources as described . No Signak
Finally wanted to edit the enigma script as described below but there's no script in the folder. So i tried to kill enigma2 process with
killall -9 enigma2. It killed the process but just one sec later they are alive again.
I strongly assume I have to buy one of these GigaBlue Systems. I do not see that it will work on the VU+. Is anybody here who has it running on a VU+?
Thanks S
I did some testing however no sucess
1) Installed nw Image (OpenATV). No signal
2) Tried different Adapter /Sources as described . No Signak
Finally wanted to edit the enigma script as described below but there's no script in the folder. So i tried to kill enigma2 process with
killall -9 enigma2. It killed the process but just one sec later they are alive again.
I strongly assume I have to buy one of these GigaBlue Systems. I do not see that it will work on the VU+. Is anybody here who has it running on a VU+?
Thanks S
Re: minisatip binaries
Hello,
why you dont type init 4 in the ssh session?
that kills enigma2
or you go to the standby.
edit: so yes here it works on a vu+ solo 2 with the parameter above.
why you dont type init 4 in the ssh session?
that kills enigma2
or you go to the standby.
edit: so yes here it works on a vu+ solo 2 with the parameter above.
Re: minisatip binaries
Hi,
On my solose v2 it does not work with your parameters
. Which image do you use?
I have two DVB-C/DVB-T Tuners (Dual Card)
Maybe Minisatip can only handle DVB-S ?
Thanks S
On my solose v2 it does not work with your parameters
. Which image do you use?
I have two DVB-C/DVB-T Tuners (Dual Card)
Maybe Minisatip can only handle DVB-S ?
Thanks S
Re: minisatip binaries
Hi,
ok first success I got it to work. The problem was that I only tested HD channels. These channels do not work. However SD channels work.
I uploaded the log again. It starts with an SD channel (freq=378000) which works and then switch to an HD Channel (freq=426000) which does not work.
Thanks to all who helped me BTW: Here is another release compiled by VENTO which also works for me (-but not the HD Cheannels)
https://www.vuplus-support.org/wbb4/ind ... ost1327022
Thanks S
ok first success I got it to work. The problem was that I only tested HD channels. These channels do not work. However SD channels work.
I uploaded the log again. It starts with an SD channel (freq=378000) which works and then switch to an HD Channel (freq=426000) which does not work.
Thanks to all who helped me BTW: Here is another release compiled by VENTO which also works for me (-but not the HD Cheannels)
https://www.vuplus-support.org/wbb4/ind ... ost1327022
Thanks S
- Attachments
-
- minisatip.zip
- (6.75 KiB) Downloaded 498 times
Re: minisatip binaries
Hi,
With vento's version are working more channels?
About ci+.... minisatip currently supports ci only, however ci+ is next, however after vacation.
Currently I have access to a system with NTV+ but if there are issues with sky we can fix them after that...
With vento's version are working more channels?
About ci+.... minisatip currently supports ci only, however ci+ is next, however after vacation.
Currently I have access to a system with NTV+ but if there are issues with sky we can fix them after that...
Re: minisatip binaries
About the log only did u try another HD freq?
To me it seems a signal problem..
To me it seems a signal problem..