Page 1 of 3
Digibit: minisatip7 can´t tune some frequencies...
Posted: Fri May 12, 2017 11:07 pm
by nickiman
Hi,
I live in a Community building so the Satellite arrives to my home only in polarization vertical low (V/L). From the SAT connector in the wall I´ve cabled to LNB1 in the Digibit R1.
I´m running minisatip7 (0.7.4)
satip-axe-201704251332-14 in my Digibit R1 device with this configuration:
Code: Select all
#
# minisatip
#
MINISATIP="no"
MINISATIP_OPTS=""
#
# minisatip 0.5
#
#MINISATIP5="yes"
#MINISATIP5_OPTS=""
#
# minisatip 0.7
#
MINISATIP7="yes"
MINISATIP7_OPTS="-7 0:1,0:2,0:3 -L *:9750-9750-12000"
#
# inetd (httpd,ftpd)
#
INETD="yes"
#
# crond
#
CROND="yes"
#
# nfsd v3
#
NFSD="yes"
NFSD_HOTPLUG_EXPORT="*" # replace with host or subnet, '*' = world
#
# oscamd
#
OSCAMD="no"
The problem that I have is that I´m unable to scan the MUX of this frequency 11.973V meanwhile if I connect the SAT cable from the Digibit to my STB I can see that channel in that frequency.
So, what I´m doing wrong?
Thank you very much for your support.
Re: Digibit: minisatip7 can´t tune some frequencies...
Posted: Sun May 14, 2017 12:26 am
by cata
Hi,
Could you please upload minisatip log?
Thank you
Re: Digibit: minisatip7 can´t tune some frequencies...
Posted: Sun May 14, 2017 10:38 pm
by nickiman
cata wrote: ↑Sun May 14, 2017 12:26 am
Hi,
Could you please upload minisatip log?
Thank you
Yes of course...
But could you tell me where are the logs saved? I´ve found these two paths:
Code: Select all
/ # find / -name log
/tmp/var/log
/dev/log
And also, which command should I run in the sat-ip firmware to collect the correct information?... because I´m totally newbie
Thank you very much!
Re: Digibit: minisatip7 can´t tune some frequencies...
Posted: Mon May 15, 2017 11:47 am
by cata
Hi,
Check if you have /tmp/minisatip.log.
If no run:
touch /tmp/nosatip
killall minisatip
./minisatip -f -l -l -l -7 0:1,0:2,0:3 -L *:9750-9750-12000
Then capture the output after the failure.
Thanks
Re: Digibit: minisatip7 can´t tune some frequencies...
Posted: Mon May 15, 2017 7:17 pm
by nickiman
Ummm... not sure I´ve got the correct logs... anyways here is the output of the commands listed:
from this route: /root
Code: Select all
~ # touch /tmp/nosatip
~ # killall minisatip
killall: minisatip: no process killed
~ # ./minisatip -f -l -l -l -7 0:1,0:2,0:3 -L *:9750-9750-12000
-sh: ./minisatip: not found
So, I´ve searched the command and I´ve run it with the complet path:
Code: Select all
/ # ./sbin/minisatip -f -l -l -l -7 0:1,0:2,0:3 -L *:9750-9750-12000
./sbin/minisatip: invalid option -- '7'
[15/05 19:07:44.069]: map_int: s not a number: *:9750-9750-12000, v=(nil), NULL NULL
[15/05 19:07:44.070]: Starting minisatip version 0.1.84-axe2, compiled with AXE DVB API, DVR buffer 18424 bytes
[15/05 19:07:44.071]: New UDP socket 3 bound to 0.0.0.0:1900
[15/05 19:07:44.071]: setting multicast for 239.255.255.250
[15/05 19:07:44.071]: New UDP socket 4 bound to 239.255.255.250:1900
[15/05 19:07:44.071]: tcp_listen: failed: bind(): Address already in use
[15/05 19:07:44.072]: RTSP: Could not listen on port 554
The file nosatip is empty:
Code: Select all
/tmp # ls -la
total 8
drwxrwxrwt 3 root root 140 May 15 19:03 .
drwxrwxr-x 14 root root 0 May 15 19:07 ..
-rw-r--r-- 1 root root 3 Jan 1 2015 bootid
-rw-r--r-- 1 root root 0 May 15 19:03 nosatip
-rw-r--r-- 1 root root 0 Jan 1 2015 satip-network
-rw-r--r-- 1 root root 266 Jan 1 2015 stv6120-init.txt
drwxr-xr-x 6 root root 120 Jan 1 2015 var
Keep in touch...
Re: Digibit: minisatip7 can´t tune some frequencies...
Posted: Tue May 16, 2017 12:24 am
by cata
I suppose minisatip7 is already running.
Run
killall minisatip7
Try to run:
/sbin/minisatip7 -f -l -l -l -7 0:1,0:2,0:3 -L *:9750-9750-12000
Thanks
Re: Digibit: minisatip7 can´t tune some frequencies...
Posted: Tue May 16, 2017 11:15 am
by nickiman
cata wrote: ↑Tue May 16, 2017 12:24 am
I suppose minisatip7 is already running.
Run
killall minisatip7
Try to run:
/sbin/minisatip7 -f -l -l -l -7 0:1,0:2,0:3 -L *:9750-9750-12000
Thanks
Hi cata,
Below the link with the log details of the commands listed:
https://pastebin.com/raw/NjzUiigX
By the way, reading the logs I´ve found one thing that I can´t understand... what means these lines?
Code: Select all
[16/05 06:54:45.341]: reply -> 17 (192.168.10.2:54308) CL:1206 [sock_id 10]:
[16/05 06:54:45.341]: HTTP/1.0 200 OK
Date: Tue, May 16 06:54:45 2017 GMT
CACHE-CONTROL: no-cache
Content-type: text/xml
X-SATIP-RTSP-Port: 554
Server: minisatip/0.7.4-axe201
Content-Length: 1206
I don´t understand why appears this IP address 192.168.10.2 because this one... it´s assigned to an IP camera device.
If you need anything else just let me know.
Thank you and best regards.
Re: Digibit: minisatip7 can´t tune some frequencies...
Posted: Wed Jun 14, 2017 10:08 pm
by nickiman
Hi cata,
Any new on this issue?
Re: Digibit: minisatip7 can´t tune some frequencies...
Posted: Wed Jun 14, 2017 11:13 pm
by cata
Hi,
sorry forgot about the issue.
The parameters are 9750-9750-12000 seems wrong. The default parameters are: *:9750-10600-11700
Could you please let me know why you've set it as it is now ?
Thank you
Re: Digibit: minisatip7 can´t tune some frequencies...
Posted: Thu Jun 15, 2017 8:12 am
by nickiman
Because I´ve followed a recommendation for use minisatip7 in another forum...
I´m going to change the config file with your parameters and I´ll let you know...
Thank you very much Cata!