Digibit R1 + DUR-LINE UK124 UNICABLE JESS

Support forum for minisatip
balou1974
Posts: 23
Joined: Sat Mar 10, 2018 8:23 pm

Re: Digibit R1 + DUR-LINE UK124 UNICABLE JESS

Post by balou1974 »

Hello,

I found out few things:
- easiest way to get a channel-list for astra is using Astra SES resources
- Digibit R1 has problems with auto-negotiation, if possible set your switch to 1GBit/full duplex
- satip-axe works fine with unicable jess, all parameters you need for minisatip7 are -j and (maybe) -7
- regarding unicable lnb scr1 could be channel 0 when using minisatip

satip-axe is running fine now, no problems anymore!
Only thing I mis would be a plugin for vlc to scan for channels. Maybe this could be included in satip-axe or minisatip using web-interface?

Thanks a lot for your hints and thoughts
9000h
Posts: 89
Joined: Tue May 12, 2015 1:49 pm

Re: Digibit R1 + DUR-LINE UK124 UNICABLE JESS

Post by 9000h »

Hi,
if you set a Ethernet interface static to full duplex you have to do it also on the other end, if not the other side will do half duplex.
CU
9000h
balou1974
Posts: 23
Joined: Sat Mar 10, 2018 8:23 pm

Re: Digibit R1 + DUR-LINE UK124 UNICABLE JESS

Post by balou1974 »

Regarding ethernet speed and duplex - 1GBit/FD, seems to work without setting it on digibit r1. I think there is something wrong with the driver. I tried setting the duplex but ethtool complained that this is not possible/I think I tried with speed-setting, too and same problem. Some say using a Cat 6a cable should solve all problems, maybe. At the moment I use Cat 5e and a 8-port tp-link smart managed GBit switch and set the port to 1GBit/FD. Seems to work, but there is much more work needed on the drivers I think(chipset manufacturer).
misaal
Posts: 1
Joined: Wed May 02, 2018 7:49 am

Re: Digibit R1 + DUR-LINE UK124 UNICABLE JESS

Post by misaal »

Hi @balou1974

What does your configuration look like?
I also have Unicable Jess, but mine does not work.
Could this work here?

MINISATIP8_OPTS="-j 0:9-1790,1:10-1892,2:11-1994,3:12-2096 -P 1"
kianusch
Posts: 31
Joined: Fri Dec 29, 2017 10:59 pm

Re: Digibit R1 + DUR-LINE UK124 UNICABLE JESS

Post by kianusch »

What do you use "-P 1" for?

Documentation says:

-P port: use port number to listen for UDP socket in the RTP communication.

But - using port number 1 on Linux based systems is probably not a good idea.
balou1974
Posts: 23
Joined: Sat Mar 10, 2018 8:23 pm

Re: Digibit R1 + DUR-LINE UK124 UNICABLE JESS

Post by balou1974 »

Actually I use this to start minisatip8:
MINISATIP8="yes"
MINISATIP8_OPTS="-j 0:0-1210,1:1-1420,2:2-1680,3:3-2040 -7 0:1,
0:2,0:3 -p http://www.satip.info/Playlists/ASTRA_19_2E.m3u"
Post Reply