I use diseqc 1.0, 4 prots
port 1 = LNB 5150
port 2 = LNB 11300
port 4 = LNB 10750
How to set diseqc and LNB?
I tried it, but there was all no signal.
./minisatip -L 1:05150-05150-11700,3:11300-11300-11700,4:10750-10750-10750
There is no any parameter can only received 11g signal , No 12g signal (port4)
./minisatip
thank you!
How to set diseqc and LNB parameters?
Re: How to set diseqc and LNB parameters?
Hi,
what is 5150 ?
Thanks
what is 5150 ?
Thanks
Re: How to set diseqc and LNB parameters?
hi cata.
5150 is C band LNB
5150 is C band LNB
Re: How to set diseqc and LNB parameters?
Hi,
for parameter 4 you can try default:
-L 4:9750-10600-11700
With 10750-10750-10750, you are saying that everything that is over 10750 should use 10750 as switch frequecy. Are you sure your LNB has 10750 as switch frequemcy ?
About C Band I am not sure is supported (never tried), but if you want it to work, upload a log.
Thanks
for parameter 4 you can try default:
-L 4:9750-10600-11700
With 10750-10750-10750, you are saying that everything that is over 10750 should use 10750 as switch frequecy. Are you sure your LNB has 10750 as switch frequemcy ?
About C Band I am not sure is supported (never tried), but if you want it to work, upload a log.
Thanks
Re: How to set diseqc and LNB parameters?
Hi.
I didn't get the answer I wanted.
The parameter -L is setting of the adapter, not the diseqc port
I only have one adapter.
How to set diseqc port and LNB?
Yes , The following Settings work fine of prot 4
But the other port no signal
minisatip -L 0:10750-10750-10750
Should be used -D parameter?
Thanks
I didn't get the answer I wanted.
The parameter -L is setting of the adapter, not the diseqc port
I only have one adapter.
How to set diseqc port and LNB?
Yes , The following Settings work fine of prot 4
But the other port no signal
minisatip -L 0:10750-10750-10750
Should be used -D parameter?
Thanks
Re: How to set diseqc and LNB parameters?
Diseqc 1.0 is the default setup. The client can select which port to use based on the configuration. If you have multiple LNBs with different switch frequency connected to the same diseqc switch connected to 1 adapter, then it will not work.
For example in tvh you can say 'Satellite Positions' 4 and tvh will add src=2 to the satip request to select port 2 of the switch
For example in tvh you can say 'Satellite Positions' 4 and tvh will add src=2 to the satip request to select port 2 of the switch
Re: How to set diseqc and LNB parameters?
I understand Diseqc is set at tvheadend.
But there is no LNB setting in tvheadend satip
Because I use LNB of different frequencies, I need to set them separately.
I only have a Diseqc 1.0 switcher
How do I set the LNB frequencies for port1 and port4, respectively
The current method only works with adapter 0.
thank you
But there is no LNB setting in tvheadend satip
Because I use LNB of different frequencies, I need to set them separately.
I only have a Diseqc 1.0 switcher
How do I set the LNB frequencies for port1 and port4, respectively
The current method only works with adapter 0.
thank you
Re: How to set diseqc and LNB parameters?
Yes there is no way to do that currently. The only workaround would be to connect individually the LNBs to different adapters.
If you are a programmer you could try to add support for it
If you are a programmer you could try to add support for it
Re: How to set diseqc and LNB parameters?
Thank you for your reply.
I only know a little basic programming.
This project is too difficult for me.
Sorry for not being able to provide support.
Best day ever.
I only know a little basic programming.
This project is too difficult for me.
Sorry for not being able to provide support.
Best day ever.